Huijue checks optical module alarms

Checking Whether Optical Module Types Match

For example, the transmission distance supported by OM1 optical fibers in the preceding command output is 150 m. If the actual transmission distance exceeds 150 m, use an optical fiber with a longer

ALM-3276800033 Optical Module Detection Failed_V200 LSW

If so, collect alarm information and configuration information, and then contact technical support personnel. If not, replace the optical module with a Huawei-certified one.

Disabling the Optical Module Alarm Function

The device has two types of optical module power alarms: warning and alarm. A warning is reported when the difference between the actual power and vendor-defined threshold is not great. It can also

Checking Whether the Rx and Tx Optical Power of the Interfaces at

If only the number of B3 bit errors increases, check whether the link directly connecting the remote router and SDH transmission device is working stably. If the link is a pure WDM link, check the

Laser Module Mismatch

The logical configuration and physical optical module type mismatch lead to reporting the LASER_MODULE_MISMATCH alarm, the client side SFP module customer used is grey module, so

How Huawei CE & S Series Switches Handle Non-Certified Optical

Huawei CE and S series switches both incorporate an optical module authentication mechanism. On S series switches, authentication is strict and alarm notifications

ALM-3276800022 Indicates that optical module power abnormal

Procedure Run the display transceiver verbose command to check the power of the optical module. Check whether the interface status and data forwarding are normal. If so, run the

SFP CHECK_SUM_FAILED Alarm: Causes & Fix | EDGE Optical

CHECK_SUM_FAILED means your switch cannot verify the SFP EEPROM data. Why third-party transceivers trigger this alarm and how to clear it without swapping the module.

Disabling the Optical Module Alarm Function

Some optical modules can continue working properly when the actual optical power is at the warning level. You can disable the alarm function for these optical modules to prevent these optical modules

Disabling the Alarm Function for Optical Modules That Are Not

This facilitates optical module management and maintenance. To avoid these alarms, disable the alarm function for optical modules that are not certified for Huawei data center switches.

forum.huawei

We''re sorry but web site doesn''t work properly without JavaScript enabled. Please enable it to continue. Loading

Setting Optical Power Alarm Thresholds

The default optical power alarm thresholds of an optical module are fixed and cannot be changed. These thresholds are determined through extensive testing and verification.

Optical Module: Typical Optical Module Troubleshooting Procedure

Check the model of the faulty optical module. If it is not a Huawei-certified optical module, replace it with a Huawei-certified optical module. If the optical module is installed on a GE port, run the display

Checking Whether Optical Module Types Match

Replace it with a Huawei-certified optical module. If an LOS alarm is displayed in the Alarm information field, the local interface does not receive any optical signal from the remote interface. The remote

Common Non-Certification Alarm Messages For Switches

To restrict the use of third-party modules on their devices, host manufacturers usually conduct inspections on the optical modules that are connected, including but not limited to reading the optical

Disabling the Alarm Function for Optical Modules That Are Not

Context If optical modules that are not certified for Huawei data center switches are used on devices, the devices will generate a large number of alarms to prompt users to replace these optical modules with

Configuring the Alarm Function for Optical Modules

You can configure the alarm thresholds for the power of optical modules to shield unnecessary alarms. To check alarm information, diagnostic information, and manufacturing information about an optical

ALM-3276800000 Indicates that SFP is not certified 136192

Procedure If this optical module was delivered from Huawei earlier, run the transceiver phony-alarm-disable command to disable the alarm function for non-Huawei customized optical

Configuring the Alarm Function for Optical Modules

You can configure the alarm thresholds for the power, temperature, current, and voltage of optical modules, and the interval at which the inter-integrated circuit (I2C) collects optical module alarm

How To Turn Off Alarms For Third-Party Modules On Huawei Switches

By default, numerous alarm messages will be generated when a non-original Huawei module is used. Huawei provides dedicated commands to disable alarms triggered by uncertified

Huawei enterprise switches

See the interface module via the optical display command information, including general information of the optical module, manufacturing information, and alarm information.

ALM-3276800022 Indicates that optical module power abnormal 136194

Replace the optical module, and check whether the alarm is cleared. If so, the alarm handling ends. If not, collect alarms, logs, and configurations, and contact technical support personnel. Was this page

Common Faults of CE Switches and How to Locate Faults

To ensure normal communication between two optical interfaces, check for transmit and receive power alarms after the two interfaces have optical modules installed and connected using an optical fiber.

ALM-135462942 The optical module is invalid 136221

Procedure Run the display transceiver slot slot-id verbose command in the system view to check whether the transmit power Tx Power of the optical module is within the allowed range. If so, services

How To Turn Off Alarms For Third-Party Modules On Huawei Switches

Huawei switches will authenticate the access optical module, and when the access module is verified to be non-Huawei original, a large number of alarm messages will pop up in the

DEVM/1/hwOpticalUnAuthorized_active

In versions earlier than V200R001C00, after the alarm function is disabled, the generated alarms will not be automatically cleared. To clear these alarms, remove and then install the optical module.

Huawei Technical Support

Learn how to display optical module information on Huawei devices using specific commands and understand the diagnostic details of optical modules.

Checking Whether Optical Module Types Match

ALM-3276800033 Optical Module Detection Failed_V200 LSW

Disabling the Optical Module Alarm Function

Checking Whether the Rx and Tx Optical Power of the Interfaces at

Laser Module Mismatch

How Huawei CE & S Series Switches Handle Non-Certified Optical

ALM-3276800022 Indicates that optical module power abnormal

SFP CHECK_SUM_FAILED Alarm: Causes & Fix | EDGE Optical

Disabling the Optical Module Alarm Function

Disabling the Alarm Function for Optical Modules That Are Not

forum.huawei

Setting Optical Power Alarm Thresholds

Optical Module: Typical Optical Module Troubleshooting Procedure

Checking Whether Optical Module Types Match

Common Non-Certification Alarm Messages For Switches

Disabling the Alarm Function for Optical Modules That Are Not

Configuring the Alarm Function for Optical Modules

ALM-3276800000 Indicates that SFP is not certified 136192

Configuring the Alarm Function for Optical Modules

How To Turn Off Alarms For Third-Party Modules On Huawei Switches

Huawei enterprise switches

ALM-3276800022 Indicates that optical module power abnormal 136194

Common Faults of CE Switches and How to Locate Faults

ALM-135462942 The optical module is invalid 136221

How To Turn Off Alarms For Third-Party Modules On Huawei Switches

DEVM/1/hwOpticalUnAuthorized_active

Huawei Technical Support

People also like:

Get In Touch

Connect With Us

Email

Poland (Sales & Engineering HQ)

Germany (EU Technical Support)

Headquarters & Manufacturing