THE ULTIMATE GUIDE TO POWER OVER ETHERNET SWITCHES

High Temperature Resistance Selection Guide for Power System Grade SFP Optical Modules

High Temperature Resistance Selection Guide for Power System Grade SFP Optical Modules

This guide reviews Germany's leading industrial-grade SFP module Manufacturers and suppliers — those who design SFP module hardware and optical transceivers built to industrial specs — and explains procurement considerations for rugged and high-temp use cases. So when choosing a transceiver that would be best suited for your needs, it is best to check which temperature range would be best. Choosing the right SFP module and reliable supplier is crucial for rail, energy, oil & gas, and factory automation projects. An industrial SFP (Small Form-factor Pluggable) module is specifically designed to address these challenges.

Read More
High Temperature Resistance Selection Guide for Tunable Photovoltaic Modules Used in Photovoltaic Power Plants

High Temperature Resistance Selection Guide for Tunable Photovoltaic Modules Used in Photovoltaic Power Plants

The PD IEC TS 63126:2025 standard provides comprehensive guidelines for qualifying PV modules, components, and materials specifically designed to operate under high-temperature conditions. In the ever-evolving world of solar energy, ensuring the reliability and efficiency of photovoltaic (PV) modules is paramount. IEC TS 63126 specifies additional testing requirements for photovoltaic modules deployed in conditions that result in higher module temperatures that are beyond the scope of IEC 61215-1 and IEC 61730-1, as well as the associated component standards, IEC 62790, and IEC 62852. How do we apply Level 1 and Level 2? * - Following publication of IEC 62788-2-1, pass/fail requirements from this document shall be followed. What governs wind load? Predominantly, three things: Typical, flat-plate PV modules with typical frames are not one of the three governing factors.

Read More
PoE power supply issues for switches

PoE power supply issues for switches

If your Cisco switch PoE is not working, the most common causes are an exhausted PoE power budget, a disabled inline power configuration, physical cable faults, incompatible powered devices (PD), or a crashed PoE controller. When a problem occurs with PoE, in most cases, the error symptom can be simply shown as the PoE switch not providing power, and the powered devices will stop. Cisco recommends that you have knowledge of these topics: • Catalyst 9000 Series switches • Power over Ethernet This document is not restricted to specific software and hardware. Power over Ethernet (PoE) technology plays a vital role in modern network infrastructure by simplifying device deployment — delivering both power and data over a single Ethernet cable.

Read More
The Role of Dual Power Supplies in Core Switches

The Role of Dual Power Supplies in Core Switches

A dual power supply setup provides a crucial backup, ensuring the switch remains operational even if one power supply fails. This translates to increased network uptime, a key consideration for any environment where consistent connectivity is. But have you ever noticed some switches boasting two power supplies? The simple answer is redundancy. This guide covers everything from fundamental concepts and configuration steps to best practices, practical examples, PoE budget planning, and buying advice to help you optimize your network. Is there any harm in connecting the two DC inputs of a Cisco IE2000 to the same power supply? I understand that this not fully redundant- but I see from a previous employee response (copied below) that DC-A and DC-B are inputs to two separate internal power supplies. This article explains the differences and helps you understand which approach fits your application.

Read More
Normal optical power values ​​for switches

Normal optical power values ​​for switches

Transmit power is typically good when it is in the 6 dB range between -1 and -7 dBm. For network engineers working with fiber optics (SFP, SFP+, QSFP), understanding TX (Transmit) and RX (Receive) signal strength is critical. Is that bad? Indicative of just needing the ports on either end cleaned and the cable?This article is intended to assist with the interpretation of the SFP transceiver TX and RX power readings available from the CLI. Connectrix: How to troubleshoot Fibre Channel node to switch port or SFP communication problems by elimination.

Read More

Get In Touch

Connect With Us

📧

Email

[email protected]

📱

Poland (Sales & Engineering HQ)

+48 22 538 72 19

🇪🇺

Germany (EU Technical Support)

+49 30 983 21 44

📍

Headquarters & Manufacturing

ul. Postępu 14, 02-676 Warszawa, Poland